The common faults of barriers mainly include the following solutions:
1. Loose wire embedment: When the local coil cannot be firmly fixed in the nest, the vibration of the car pressing the road surface will cause the coil in the nest to deform and change the initial inductance of the ground. At this time, the sensor must be reset before it can work normally. The solution is to put the molten asphalt in place and fix it.
2. Loosen the wire: The hinge screw is connected with the positive and negative threads, and the upper and lower two bearings are connected with the double-headed screw. If the screw is loose, the upper and lower positions will be inaccurate. Use a 80mm long Ф4 iron rod to insert the double-headed screw to adjust the brake lever up and down in place.
3. Looser screw loose: If this screw is loose, it will cause the upper and lower positions of the brake rod to be inaccurate, and the swinging of the lever will be large. The bolts will be tight and the nuts can be locked.
4, in place to control the magnet shift position: up and down in place are used Cimin Hall element, if the rectangular magnet and reducer cam with the cam position changes, resulting in in place is not accurate. Adjust it accurately and not flip it to solve the problem.
5, power failure protection switch power failure: When the control part of the machine fails, the machine's automatic protection device will automatically work, this time the brake lever stopped at the oblique position does not move, the total power is off, the machine does not work. At this point, the machine door is opened, and the large belt can be restored by rotating the large belt 3-8 times clockwise. If it cannot be restored to this condition many times, check whether the Hall element and the circuit board have malfunctioned.
6. The pull-down hook adjusts the looseness of the nut: the lower part of the chassis is provided with a pull-down hook of thread M10, and its function is to pull the spring of the balance mechanism and the zero adjustment of the balance function. It is equipped with two M10 hexagon nuts and ten spring washers. If the nut is loose, knocking noise and balance will occur when the machine is running. Even if the machine can run after the imbalance, it will greatly increase the speed reducer, motor and Other transmissions. The load of the parts affects the reliability and the mechanical life.
Welcome to click on the company's Daozou products
1. Loose wire embedment: When the local coil cannot be firmly fixed in the nest, the vibration of the car pressing the road surface will cause the coil in the nest to deform and change the initial inductance of the ground. At this time, the sensor must be reset before it can work normally. The solution is to put the molten asphalt in place and fix it.
2. Loosen the wire: The hinge screw is connected with the positive and negative threads, and the upper and lower two bearings are connected with the double-headed screw. If the screw is loose, the upper and lower positions will be inaccurate. Use a 80mm long Ф4 iron rod to insert the double-headed screw to adjust the brake lever up and down in place.
3. Looser screw loose: If this screw is loose, it will cause the upper and lower positions of the brake rod to be inaccurate, and the swinging of the lever will be large. The bolts will be tight and the nuts can be locked.
4, in place to control the magnet shift position: up and down in place are used Cimin Hall element, if the rectangular magnet and reducer cam with the cam position changes, resulting in in place is not accurate. Adjust it accurately and not flip it to solve the problem.
5, power failure protection switch power failure: When the control part of the machine fails, the machine's automatic protection device will automatically work, this time the brake lever stopped at the oblique position does not move, the total power is off, the machine does not work. At this point, the machine door is opened, and the large belt can be restored by rotating the large belt 3-8 times clockwise. If it cannot be restored to this condition many times, check whether the Hall element and the circuit board have malfunctioned.
6. The pull-down hook adjusts the looseness of the nut: the lower part of the chassis is provided with a pull-down hook of thread M10, and its function is to pull the spring of the balance mechanism and the zero adjustment of the balance function. It is equipped with two M10 hexagon nuts and ten spring washers. If the nut is loose, knocking noise and balance will occur when the machine is running. Even if the machine can run after the imbalance, it will greatly increase the speed reducer, motor and Other transmissions. The load of the parts affects the reliability and the mechanical life.
Welcome to click on the company's Daozou products
Knife Wet Stone,Wet Stone Sharpening Kit,Hand Held Grinding Stone,Best Knife Sharpening Stone
ZHE JIANG DONGYANG WEIWEI INOUSTY COMMERCE CO.,LTD , https://www.cnwwsy.com