With the continuous improvement of people’s quality of life, sanitary products are also diverse, and showers are also important items in bathrooms. The installation methods for showers are also surface mounted, concealed, walled, and ceiling mounted. Different installations will also have different effects. Everyone must be based on the actual situation of their own home when installing the shower. There are many things to pay attention to in the shower installation process. If you also have the needs in this area, you may wish to learn more about the relevant content.
First, shower installation dimensions and precautions:
There are two kinds of installation scales for shower: In accordance with the relevant regulations, the center of the buried shower wall with a dark showerhead should be 2.1 meters away from the ground, and the center of the shower switch should be 1.1 meters away from the ground; The shower surface is defined and the distance is preferably 2 meters. It should be noted that these data are only average data. The actual installation time of the shower is adjusted by everyone's height.
The surface-mounted shower switch buried water pipe is left hot and right-cold, and the center distance should be 150cm. The wall surface shall be flush with the tile surface and the internal buried water pipe shall be perpendicular to the wall surface. After the shower is installed, it shall be the wall. The face is at a 90-degree angle. In addition, water pressure regulation is also a key: Under normal circumstances, the water pressure within 1.5 kg is most suitable for the use of showers, water pressure over the assembly caused by violent showers, water pressure too small shower can not be used normally.
Second, shower installation steps:
1. First, prepare a few tools needed to install the shower: drill, screwdriver, ruler, hammer (if lack of drilling, hammer and other tools can be rented to the bathroom hardware store).
2, look at the instructions, and then measure the size with a tape measure, determine the shower installation location and shower installation height, and make a mark.
3. Place the shower support in the marked position and use a pencil to mark the specific location where the hole is to be drilled.
4. According to the position just made, make a hole in the wall.
5. Punch the expansion sleeve of the expansion screw into the hole that has been made, and tighten the round bottom cover of the fitting to the wall with a screw.
6. Install the shower pole on the wall, stabilize the upper fixing point, and then fix the lower position.
7. After confirming that all the screws on the inner attachment angle of the fixed point are screwed in, perform detailed adjustments.
8. Tighten the shower hose and install and install the hand shower. The entire installation step is completed.
Editor's summary: there are many steps to install the shower, all kinds of details must pay attention to, if you do not know how to install the shower may wish to install the professional chef, and other shower installation related issues for everyone to introduce here, hoping to help you For more information, please follow this site.
Shower shower
Diamond grinding head: A kind of stone material, ceramic materials and other non-metallic materials of grinding tools, especially involving a with diamond alloy grinding tools for grinding body, it includes substrate and a mill body, in which several mill body clearance to fixed to the substrate, the grinding surface of the grinding head grinding body also set a clearance, among them, the substrate is best by a certain toughness of adhesive materials, The abrasive body is preferably made of diamond alloy material. The utility model has the characteristics of high grinding performance, simple manufacture, low cost, high grinding quality and can be applied to large-scale grinding
Through the processing of various workpiece, to achieve grinding, grinding, polishing effect; According to the use, mainly divided into the following types of grinding head:
1.grinding class: mainly installed in the grinding machine grinding head, the workpiece for grinding, grinding, grinding, processing can be divided into rough grinding and fine grinding.
2.grinding class: generally used for grinding the burr of the workpiece, or the workpiece surface precision is not high processing. Use grinding machine, electric, pneumatic and other tools to high-speed operation to achieve the effect of grinding.
3.polishing class: specially for surface finish (roughness) processing and use of higher requirements, is the need for separate processing process.
Diamond Grinding Heads,Diamond Bit Set,Diamond Cut Off Wheel,Diamond Stone Grinding Wheels
Henan Jinlun Superhard Material Co., Ltd , https://www.jinlunsuperhard.com